What happens before anything touches the paint, and how the wash itself avoids scratches.
A thick layer of soap sprayed onto the car from a foam cannon before anyone touches the paint. It sits for a few minutes, softens dirt and pollen, then gets rinsed off with the loose grit in it. Less grit on the panel means fewer scratches once the wash mitt goes on. A foam wash starts every ceramic coating prep.
A hand-wash method with one bucket of soapy water and a second bucket of plain rinse water. The mitt is rinsed after every panel, so the dirt it picked up drops out there instead of going back onto the paint. It is one of the simplest ways to stop a wash from adding swirl marks, and worth copying at home between details. More in the car care guide.
A plastic grate that sits at the bottom of a wash bucket. Dirt rinsed off the mitt sinks through it and stays below, where the mitt cannot pick it back up. Paired with the two-bucket method, it keeps the water the mitt touches cleaner for the whole wash. It costs little and pays off on dark paint, where every fine scratch shows in the Florida sun. See what paint correction fixes.
A car soap that is neither acidic nor alkaline, so it lifts dirt without stripping wax, sealant or ceramic coating. Dish soap and strong degreasers can dull protection and dry out rubber trim. On a coated car, a pH-neutral shampoo is the everyday wash soap that helps the coating reach the long end of its life. See how to make a coating last.
A towel woven from very fine synthetic fibres that trap dust and water instead of pushing them across the paint. Detailers keep separate towels for paint, glass, wheels and interiors, so grit from one job never reaches another. Wash them on their own, without fabric softener, which clogs the fibres. A dirty or dropped towel is a common cause of fresh swirl marks. See car detailing.
Removing what a normal wash leaves behind, in two ways. Chemical decontamination dissolves it, for example an iron remover for brake dust. Mechanical decontamination lifts it off, usually with a clay bar. The paint has to be this clean before polishing or a coating, because anything left on the surface gets ground in or sealed under it. It is step one of the ceramic process.
A soft, putty-like bar that glides over lubricated paint and pulls out bonded grime such as tree sap mist, overspray and rail dust. Test it yourself: run your fingertips over clean paint inside a thin plastic bag, and if it feels gritty, it needs clay. The result is glass-smooth paint ready for polish or protection. A clay bar treatment is an add-on to any car detailing package.
A spray that dissolves tiny iron particles, mostly hot brake dust and rail dust, that embed in paint and wheels and later rust into orange specks. Most iron removers turn purple as they react, which shows where the iron was. It goes on before the clay bar, so the clay has less to drag across the paint. An iron remover is part of the prep for every ceramic coating.
Cleaning a lightly dusty car with a spray that surrounds the dirt so it can be wiped off with microfiber towels, with no bucket and no rinse. It suits a car that is only dusty. On a car covered in sand, mud or lovebugs it risks scratching, because the grit is dragged across the paint. OCD brings its own water to every job, so this entry is a definition, not a description of his process.
A wash done from one bucket of water mixed with a special polymer solution, using a mitt or towels, with no hose rinse afterwards. It uses far less water than a hose wash and handles more dirt than a waterless spray. It is common in apartments and garages where a hose is not allowed. Heavy dirt still needs a proper pre-rinse first. For a routine that suits Florida, see the car care guide.
Detailing done where the car is parked, at home or at work, by a detailer who brings the water, power and tools. Obsessively Clean Detailing is mobile only: Nick Russell is based in Apopka and comes to 19 nearby towns, including Orlando, Sanford and Clermont. You skip the drive and the waiting room. See the service area and the car detailing packages.
A drive-through wash. Tunnel washes with spinning brushes or cloth strips can drag grit from earlier cars across your paint, a common source of swirl marks on dark cars. Touchless washes avoid contact but rely on strong chemicals that can wear down wax and sealant faster. Either is better than leaving lovebugs or bird droppings to bake on. Paint already marked by them can be fixed with paint correction.
A product wiped onto clean tire sidewalls to give them a dark satin or glossy finish and to slow fading and browning. Water-based dressings look natural and fling less onto the paint; solvent-based ones shine more. It goes on after the wheels and tires are scrubbed. Nick’s clip of a lifted Super Duty on the car detailing page shows the finished look.
Cleaning the engine compartment with degreaser, soft brushes and a low-pressure rinse, then dressing the plastics. Sensitive parts such as the alternator, air intake and exposed electrical connectors are covered first, and the engine should be cool. A clean bay also makes leaks easy to spot. Engine bay cleaning is not a listed OCD service; ask when you contact Nick if you want it.